Aniimo Auto Reconnecting Loop problems received a direct fix in Version 1.1, with Pawprint Studio saying it resolved an issue where the client could enter an infinite reconnection loop under certain circumstances. If you were hitting that specific bug before September 23, updating and restarting the client should now be the first step.
That fix does not mean every disconnect or reconnect message is gone. Aniimo can still lose its connection because of Wi-Fi interference, VPN or proxy routing, regional latency, heavy server load or a local network problem. If the loop remains on the latest build, use the checks below to separate a fixed client bug from a current connection issue.
Was the Aniimo Auto Reconnecting Loop Fixed?
Aniimo Auto Reconnecting Loop Image Pawprint Studio.
Yes, one cause of the Aniimo Auto Reconnecting Loop was fixed in Version 1.1. The official September 23 update notice lists an issue where the client could enter an infinite reconnection loop under certain circumstances among the resolved performance and bug problems.
Pawprint Studio does not say that every reconnection symptom had one cause, so players should not interpret the patch note as a promise that all network failures are impossible. Make sure the client is fully updated before doing anything else, especially if an older installation was left open during maintenance.
Restart and Verify the Latest Client First
Fully close Aniimo rather than leaving it suspended, then reopen the game after the update has completed. If you are on mobile and still have a client from an earlier test, uninstall it and download the live release. Old test clients are no longer supported.
If the Aniimo Auto Reconnecting Loop appeared because of the client bug fixed in Version 1.1, this is the point where it should stop. If it continues, move to network troubleshooting rather than repeatedly reinstalling the same current build.
Turn Off VPNs, Proxies and Private DNS
Aniimo’s official mobile FAQ tells players with connection errors to disable VPNs and proxies. For download and connection problems it also calls out Private DNS, ad blocking tools and, on iOS, iCloud Private Relay. These services can change how the game reaches its servers and make a normal connection harder to diagnose.
Disable them temporarily, restart the game and test again. If the Aniimo Auto Reconnecting Loop disappears, re-enable services one at a time to identify which one is interfering. Do not change several router and phone settings at once because that makes the actual cause much harder to find.
Switch Networks and Use 5 GHz Wi-Fi
Switch between Wi-Fi and mobile data to see whether the issue follows the device or the network. Pawprint Studio also recommends 5 GHz Wi-Fi where possible because 2.4 GHz is more prone to interference. Restarting the phone and router is part of the official connection troubleshooting sequence.
If the Aniimo Auto Reconnecting Loop happens only on home Wi-Fi but mobile data works, focus on the router, DNS and local connection. If it happens on multiple unrelated networks, checking Aniimo’s server status and the Aniimo Auto Reconnecting Loop client state becomes more important.
Check the Regional Server
Connecting to a server in a different region can add latency. Aniimo recommends using a server in your own region for the best connection. This matters even more on mobile data, where signal changes while moving can already introduce packet loss.
Remember that Aniimo stores progress independently between servers. Do not switch to another region as a permanent workaround without understanding that you may see separate character progress. For the Aniimo Auto Reconnecting Loop, the goal is to diagnose the connection while keeping your intended account and server intact.
Could Aniimo Servers Be Under Heavy Load?
Yes. The official FAQ warns that peak download and launch periods can put servers under heavy load. If many players are reporting connection failures at the same time, a local reinstall may achieve nothing. Check the current server situation before repeatedly deleting game files.
For an isolated Aniimo Auto Reconnecting Loop after the Version 1.1 fix, test another network and restart the router. For a widespread outage, wait until the service is healthy before judging whether the loop still affects your device.
When to Contact Aniimo Support
If you are on the latest Version 1.1 client, have tested another network, disabled VPN and proxy services and confirmed there is no wider outage, collect useful details for support. Include the platform, device model, regional server, when the loop begins and whether it happens on both Wi-Fi and mobile data.
Version 1.1 removes a confirmed infinite-loop bug, so a persistent Aniimo Auto Reconnecting Loop now deserves a fresh diagnosis rather than relying on pre-patch advice. Aniimo’s English support address is support_en@aniimo.com, and a clear report should make it easier to distinguish an account, server, network or device-specific problem.
